#Dane elec usb write protected portable

SO EXTREME SUPER SPEED PORTABLE USB 3.0.

#Dane elec usb write protected software

Make sure you have a backup of the software if you are going to attempt this. PLEASE NOTE THAT THIS PROCEDURE MAY COMPLETELY BRICK OR DESTROY YOUR USB DRIVE. You can check and see if yours looks similar, or even load these settings and try them. Note вЂ“ the settings are saved in the MP.INI file.

Then you should be able to click вЂStartвЂ™ and away you go! You should see some formatting happen, then you will have to remove the drive and plug it in againвЂ¦then you should have a nice 32 gb USB drive to use.Д®DIT: For the 16 gb USB, try using -60 controller setting.

I think leave the defaults but tick the вЂErase FlashвЂ™.

So, anyway, here are the settings I chose:

The controller that I had to choose was the PS2251-90 (which is a bit weird, because the chip said it was a 2251-60, but that didnвЂ™t work).

Choose вЂAdvanced SettingвЂ™ and вЂNew SettingвЂ™ and OK.

You should be able to get an output that looks something like this: Put in your drive letter and click вЂReadвЂ™.

#Dane elec usb write protected trial

This wasnвЂ™t such an easy thing to doвЂ¦but hopefully you wonвЂ™t have to, now that I have done it for you!Д®DIT-3 Others seem to have had success with Silicon Power Formatter, or preformat.exeД®DIT-4 You may want to try Formatter first вЂ“ Craig at iRevit has hosted the Formatter.zip and tested it (May 2012)ДЇrom here, it was a bit of trial and error. I dismantled a spare USB key that we had received for Building Design Suite Premium.

#Dane elec usb write protected how to

Via CAD Forum вЂ“ How to re-format the Autodesk instalation USB key? This procedure may lead to a damage of your USB key and is completely unsupported. Then click Start.Д«e warned! Make sure you have a backup copy of your original installation files. Start the downloaded EXE and click вЂњReset Write ProtectвЂќ, W.P select Un-Write Protect. This tool can be downloaded here (file MI_ReFixInfo_1_0_0_1.7z). To overwrite this USB key you can use the utility SMI ReFixInfo. Autodesk Product Design Suite Ultimate 2013 uses the USB key of the type вЂњDaneElec zMate AeroвЂќ (blue) вЂ“ see Dane-Elec вЂ“ with the controller SM3254Q AE. If you want to вЂњmisuseвЂќ this USB memory to store your data you can вЂњhackвЂќ it with internal reformatting, make it a standard R/W device.Д®.g. The installation USB flash memory (key, dongle) used for distribution of Autodesk Design Suites is a read-only device and cannot be overwritten or formatted with standard methods. I used smi_mptool_v2.03.34_v7_j1118_3254ae and now it works.ДЄfter few minutes the device is ready to use.Д®DIT 6 вЂ“ for Autodesk Product Design Suite Ultimate 2013 Inside my USB Drive (also named DaneElec zMate USB 32 GB) I found a controller SM3254Q AE, produced by SMI. Format the drive using the Windows format tool (or other tool of your choice) as NTFS.Д®DIT вЂ“ 5 From the comments, for DaneElec zMate USB 32 GB: Unplug your USB drive and plug it back in.ДҐ. Download the file from this linkвЂ¦ and extract it to your drive.ДЈ. I found a solution for the latest drive that I received with the PS2251-67 Controller.ДЎ.

Set Controller to PS2251-62 and FC1-FC2 to 01Д®DIT 7 вЂ“ For PS2251-67 (From Ryan Ruta in the Comments) Run getinfo in MPALL_F1_9000_v363_0C folder

#Dane elec usb write protected code

In Firmware tick вЂDo ISPвЂ™ вЂErase Code BlockвЂ™ and вЂAuto ISPвЂ™

Set Controller to PS2251-67 and FC1-FC2 to 01 Recieved Brand New USBвЂ™s For Autodesk Design Suite 2013 PremiumДownload MPALL_F1_9000_v363_00 and MPALL_F1_9000_v363_0C You can try this process in MPALL (step 1 above):

Run MPALL 363 c (as per settings below) (make sure its revision C).

This may seem a bit long winded, but I think it might be a good way for 2013 media kit: YOU MUST USE USB3Д¬opy the contents between the = to a new file named 2014_2251-03.iniД¬lick Setting, select вЂњAdvanced SettingвЂќ then press OKД¬lick the load button and select the 2014_2251-03.ini file you created earlier. He also provides a link to download the proper version, at:

Do not try to force a certain BIN file onto the drives firmware using MPALL.

Do not use the formatter.zip on the latest 2014 version TOSHIBA USB 3.0 with the 2251-03.

Click start, the process lasts for about a minute and itвЂ™s doneWARNINGSThere is some evidence of newer drives being bricked.

Close settings window by clicking on вЂњxвЂќ.

Choose advance settings and load the ini file, the same that Mike created.

Start it, put your usb stick into your USB 3.0 port.